CMOS - Setup Utility für das Gigabyte P35-DS3 BiosVer. F13a |
|
Standart CMOS Feature |
|
| IDE Channel 0 Master | Samsung HD250HJ |
| IDE Channel 1 Master | Samsung HD501LJ |
| IDE Channel 2 Master | CD-Rom |
| IDE Channel 3 Master | [NONE] |
| IDE Channel 4 Master | [NONE] |
| IDE Channel 4 Slave | [NONE] |
| IDE Channel 5 Master | [NONE] |
| IDE Channel 5 Slave | [NONE] |
| Drive A | [NONE] |
| Floppy 3 Mode Support | [DISABLED] |
| Halt On | [All, But Keyboard] |
Advanced BIOS Feature |
|
| Hard Disk Boot Priority | |
| First Boot Device | Harddisk |
| Second Boot Device | [Disabled] |
| Third Boot Device | [Disabled] |
| Boot Up Floppy Seek | [Disabled] |
| Boot Up Num-Lock | [ON] |
| Password Check | [Setup] |
| HDD SMART Capalitiy | [Disabled] |
| CPU Multi-Threading | [Enabled] |
| Limit CPUID Max to 3 | [Disabled] |
| No-Execute Memory Protect | [Enabled] |
| CPU Enhanced Halt (C1E) | [Enabled] |
| CPU Thermal Monitor 2(TM2) | [Enabled] |
| CPU EIST Function | [Enabled] |
| Virtualization Technology | [Disabled] |
| Full Screen LOGO Show | [Disabled] |
| Init Display First | [PEG] |
Integrated Peripherials |
|
| SATA AHCI Mode | [Disabled] |
| SATA Port0-1 Native Mode | [Disabled] |
| USB Controller | [Enabled] |
| USB 2.0 Controller | [Enabled] |
| USB Keyboard Support | [Disabled] |
| USB Mouse Support | [Disabled] |
| Legacy USB Storage detect | [Enabled] |
| Azalia Codec | Auto |
| Onboard H/W Lan | [Enabled] |
| -> Smart Lan | press enter |
| Onboard Lan Boot ROM | [Disabled] |
| Onboard SATA/IDE Device | [Enabled] |
| Onboard SATA/IDE Ctrl Mode | [IDE] |
| Onboard Serial Port 1 | [Disabled] |
| Onboard Parallel Port | [Disabled] |
Power Management |
|
ACPI Suspend Type |
[S3(STR)] |
| USB Device Wake-Up from S3 | Enabled |
| Soft-Off by PWR-BTTN | Instant-Off |
| PME Event Wake Up | Enabled |
| Power On by Ring | Enabled |
| Resume by Alarm | Disabled |
| HPET Support | Enabled |
| HPET Mode | 32-bit mode |
| Power On By Mouse | Disabled |
| Power On By Keyboard | Disabled |
| AC Back Keyboard | Soft-Off |
PnP/PCI Configurations |
|
Resources Controlled by |
[auto] |
| PCI Latency Timer (CLK) | [32] |
| PCI1 IRQ Assignment | [auto] |
| PCI2 IRQ Assignment | [auto] |
| PCI3 IRQ Assignment | [auto] |
PC Health Status |
|
Reset Case Open Status |
[Disabled] |
| CPU Warning Temperatur | 80 |
| CPU FAN Fail Warning | [Enabled] |
| System Fan2 Fail Warning | [Disabled] |
| Power Fan Fail Warning | [Disabled] |
| Systen Fan1 Fail Warning | [Disabled] |
| CPU Smart Fan Controll | [Enabled] |
| CPU Smart Fan Mode | [Voltage] |
MB Intelligent Tweaker (MIT) |
|
Robust Graphics Booster |
[auto] |
| CPU Clock Ratio | [9X] |
| CPU Host Clock Control | [Enabled] |
| CPU Host Frequency [MHZ] | 333 |
| PCI Express Frequency | auto |
| C.I.A.2 | disabled |
| Performance Enhance | Standart |
| System Menory Multiplier (SPD) | 2.40 |
| DRAM Timings Selectable (SPD) | Manual |
| ********** Standart Timing Control********** | |
| CAS Latency Time | (5)4 |
| DRAM RAS# to CAS# | (5)4 |
| DRAM RAS# Precharge | (5)4 |
| Precharge delay (tRAS) | (18)12 |
| ********** Advanced Timing Control********** | |
| ACT to ACT Delay (tRRD) | (3)auto |
| Rank Write to READ Delay | (3)auto |
| Write to Precharge Delay | (6)auto |
| Refresh to ACT Delay | (42)auto |
| Read to Precharge Delay | (3)auto |
| Static tRead Value | (6)auto |
| Static tRead Phase Adjust | (17)auto |
| ********** System Voltage Control********** | |
| System Voltage Control | Manual |
| DDR2 OverVoltage Control | [+0.4V] |
| PCI-E OverVoltage Control | Normal |
| FSB OverVoltage Control | Normal |
| (G)MCH OverVoltage Control | Normal |
| CPU Voltage Control | 1.29375V |
| Normal CPU Vcore | 1.28750V |